Category: chiral-catalyst

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.602-09-5,[1,1′-Binaphthalene]-2,2′-diol,as a common compound, the synthetic route is as follows.

Stirrer, condenser, and a glass reactor equipped with a thermometer, (RS) -1,1′- bi -2-naphthol 180g (0.629mol), ethylene carbonate 127g (1.439mol), was charged with potassium carbonate 9.0g and toluene 180g, 10 at 110 It was stirred time. The mother liquor 110 obtained in toluene 200g and Production Example 1 in the reaction productAfter the addition of 0g, the organic solvent layer kept at 80 , and washed with sodium hydroxide aqueous solution. SubsequentlyThe organic solvent layer, wash water was washed with water until neutral. Dee and the resulting organic solvent layerTo obtain a dehydrated crystallization solution under reflux using a Nsutaku equipment, cold in such a way that 30 after 8 hoursTo precipitate a crystal at 39 by retirement. Thus obtained slurry solution of the above-mentioned conditionsIn After filtration, further wash the crystal with toluene 200g,It was separated into the crystal section and the mother liquor . ThisIt took 10 minutes to filtration and washing operation . Also , it was analyzed to collect part of the resulting crystals , sinteredSolvent content of Akirachu is 15 wt % , the shape of the crystals was plate- shaped crystals . It is separated by filtrationThe mother liquor was 1603g. Then , drying the crystals obtained by the filtration operation (RS) -2,2′- Bis ( 2-hydroxyethoxy ) -1,1′- binaphthalene of white crystals 2Was obtained 11g (89.5% yield , HPLC purity 99.7%, YI value : 4 ) . The obtained crystalsThe physical properties as follows [DSC melting endotherm maximum : 107 , powder X-ray diffraction pattern : polymorph C,Crystal shape : plate-like crystal , aspect ratio : 1.3 (absolute value of the width : 70mum), mode diameter and jointThe ratio of the Anne diameter (Dmode / Dmedian): 1.0]., 602-09-5

602-09-5 [1,1′-Binaphthalene]-2,2′-diol 762831, achiral-catalyst compound, is more and more widely used in various fields.

Reference£º
Patent; Taoka Chemical Co., Ltd.; MATSUURA, TAKASHI; KAWAMURA, MIO; HIRABAYASHI, SHUNICHI; FUJII, KATSUHIRO; (23 pag.)JP2015/187098; (2015); A;,
Chiral Catalysts
Chiral catalysts – SlideShare

4488-22-6, [1,1′-Binaphthalene]-2,2′-diamine is a chiral-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

General procedure: In a typical experiment Pd(OAc)2 (5.6 mg, 0.025 mmol), triphenylphosphine (13.2 mg, 0.05 mmol), 17-iodo-5alpha-androsta-16-ene 1 (0.5 mmol), 2,2′-diamino-1,1′-binaphthalene 2 (varied from 1.0 mmol to 0.125 mmol) and triethylamine (0.5 mL) were dissolved in DMF (10 mL) under argon in a 100 mL three-necked flask equipped with a gas inlet, reflux condenser with a balloon (filled with argon) at the top. The atmosphere was changed to carbon monoxide. The reaction was conducted for the given reaction time upon stirring at 50 C and analysed by TLC. The mixture was then concentrated and evaporated to dryness. The residue was dissolved in chloroform (20 mL) and washed with water (3 20 mL), 5% hydrochloric acid (20 mL), saturated NaHCO3 (20 mL) and brine (20 mL). The organic phase was dried over Na2SO4, filtered and evaporated to give a solid material. All compounds were subjected to column chromatography (Silicagel 60 (Merck), 0.063-0.200 mm), EtOAc/CHCl3 or hexane/CHCl3 (the exact ratios are specified in Section 4.4 for each compound). 4.3. Characterisation of the products (Fig. 3) (Sax)-3: Yield: 410 mg (72%). Off-white yellow solid, mp 137-142 C; [Found: C, 84.55; H, 7.65; N, 4.70; C40H44N2O requires C,84.46; H, 7.80; N, 4.93]; Rf (5% EtOAc/CHCl3) 0.68. 1H NMR (CDCl3) delta: 8.94 (1H, d, 9.0 Hz, H-30), 8.03 (1H, d, 9.0 Hz, H-40), 7.94 (1H, d,8.2 Hz, H-50), 7.87 (1H, d, 8.5 Hz, H-300), 7.82 (1H, d, 7.5 Hz, H-400), 7.43 (1H, dt, 6.3 Hz, 1.6 Hz, H-60), 7.35 (1H, s, NH), 7.31 (1H, dt,8.5 Hz, 0.8 Hz, H-70), 7.29-7.26 (2H, m, H-600 , H-600), 7.23 (1H, dt,6.8 Hz, 1.1 Hz, H-700), 7.16 (1H, d, 8.7 Hz, H-80), 6.96 (1H, d, 8.2 Hz,H-800), 6.21 (1H, dd, 2.9 Hz, 1.5 Hz, H-16), 3.69 (2H, s, NH2), 2.05 (1H, ddd, 16.7 Hz, 6.5 Hz, 3.4 Hz, 15-CHaHb), 1.78 (1H, ddd,16.7 Hz, 11.9 Hz, 1.4 Hz, 15-CHaHb), 1.07-0.54 (23H, m, skeleton protons), 0.78 (3H, s, 19-CH3), 0.62 (3H, s, 18-CH3). 13C NMR (CDCl3) delta: 163.6, 150.4, 143.0, 140.0, 135.7, 133.8, 132.5. 131.1, 130.3, 129.3, 128.3, 128.2, 128.1, 127.5, 126.8, 125.3, 124.9, 123.6, 122.8, 120.4, 119.7, 118.1, 110.5, 56.8, 54.7, 47.2, 45.3, 38.4, 36.3, 34.2, 33.7, 31.8, 31.4, 29.0, 28.8, 26.8, 22.2, 20.5, 16.0, 12.1. IR (KBr, m(cm1)): 3440 (amide-NH), 3398 (NH2), 1665 (CON), 1620 (CC). MS m/z (rel int.): 569.4 (100, (M+H)+), 381 (9), MS/MS m/z (relint.): 551.4 (29), 285.2 (100). [alpha]D20 = 37.1 (c 1.34, CHCl3). (Rax)-3: Yield: 114 mg (20%). Off-white solid substance; [Found:C, 84.30; H, 7.66; N, 4.77; C40H44N2O requires C, 84.46; H, 7.80; N,4.93]; Rf (5% EtOAc/CHCl3) 0.72. 1H NMR (CDCl3) delta: 8.95 (1H, d,9.0 Hz, H-30), 8.03 (1H, d, 9.0 Hz, H-40), 7.93 (1H, d, 7.9 Hz, H-50), 7.87 (1H, d, 8.9 Hz, H-300), 7.82 (1H, d, 7.8 Hz, H-400), 7.43 (1H, dt,6.4 Hz, 1.2 Hz, H-60), 7.36 (1H, s, NH), 7.31 (1H, dt, 8.6 Hz, 0.8 Hz,H-70), 7.29-7.26 (2H, m, H-6”, H”), 7.23 (1H, dt, 6.9 Hz, 1.5 Hz,H-7”), 7.16 (1H, d, 8.5 Hz, H-8′), 6.96 (1H, d, 8.4 Hz, H-8”), 6.21 (1H, dd, 3.1 Hz, 1.5 Hz, H-16), 3.69 (2H, s, NH2), 2.05 (1H, ddd, 16.3 Hz, 6.4 Hz, 3.4 Hz, 15-CHaHb), 1.78 (1H, ddd, 16.6 Hz,11.7 Hz, 2.0 Hz, 15-CHaHb), 1.07-0.53 (23H, m, skeleton protons), 0.77 (3H, s, 19-CH3), 0.31 (3H, s, 18-CH3). 13C NMR (CDCl3) delta: 163.5, 150.4, 143.1, 140.2, 135.7, 133.8, 132.4, 131.1, 130.3, 129.3, 128.4, 128.3, 128.2, 127.5, 126.8, 125.3, 124.9, 123.6,122.8, 120.4, 119.7, 118.0, 110.6, 56.8, 54.8, 47.2, 45.2, 38.4, 36.3, 34.2, 33.7, 31.7, 31.4, 29.0, 28.8, 26.8, 22.2, 20.5, 15.5, 12.1. IR(KBr, m (cm1)): 3441 (amide-NH), 3396 (NH2), 1665 (CON), 1620 (CC). MS m/z (rel int.): 569.4 (100, (M+H)+), 381 (9), MS/MS m/z (rel int.): 551.4 (29), 285.2 (100). [alpha]D20 = +191.5 (c 0.914, CHCl3). (Sax)-4: Yield: 102 mg (12%). Beige solid substance; [Found: C,84.31; H, 8.35; N, 3.12; C60H72N2O2 requires C, 84.45; H, 8.51; N,3.28]; Rf (10% hexane/CHCl3) 0.69. 1H NMR (CDCl3) alpha: 8.94 (2H, d,9.2 Hz, H-3′), 8.08 (2H, d, 9.2 Hz, H-4′), 7.95 (2H, d, 8.2 Hz, H-5′),7.46 (2H, dt, 7.2 Hz, 0.9 Hz, H-6′), 7.35 (2H, dt, 7.2 Hz, 0.9 Hz, H-7′), 7.1 (2H, d, 9.3 Hz, H-8′), 7.13 (2H, s, NH), 6.05 (2H, dd, 3.1 Hz, 1.5 Hz, H-16), 2.02 (2H, ddd, 16.8 Hz, 6.4 Hz, 3.1 Hz, 15-CHaHb), 1.88 (2H, dd, 9.9 Hz, 3.1 Hz, 14-CH), 1.75 (2H, ddd, 16.8 Hz,11.7 Hz, 1.5 Hz, 15-CHaHb), 1.69-0.54 (44H, m, skeleton protons), 0.77 (6H, s, 19-CH3), 0.57 (6H, s, 18-CH3). 13C NMR (CDCl3) alpha: 163.6, 150.2, 140.0, 136.0, 135.2, 132.4, 131.3, 130.0, 128.2,127.5, 125.3, 124.9, 120.5, 118.1, 56.6, 54.8, 47.2, 45.4, 38.4, 36.3, 34.2, 33.6, 31.7, 31.4, 29.0, 28.8, 26.8, 22.1, 20.5, 16.1, 12.1. IR (KBr, m (cm1)): 3408 (amide-NH), 1677 (CON), 1621 (CC). MS m/z (rel int.): 853.6 ((M+H)+); 875.6 ((M+Na)+), 891.5 ((M+K)+). [alpha]D20 = +12.0 (c 0.418, CHCl3). (Rax)-4: Yield: 85 mg (10%). Beige solid substance; [Found: C,84.28; H, 8.30; N, 3.06; C60H72N2O2 requires C, 84.45; H, 8.51; N,3.28]; Rf (10% hexane/CHCl3) 0.74. 1H NMR (CDCl3) alpha: 8.95 (2H, d,9.0 Hz, H-3′), 8.08 (2H, d, 9.0 Hz, H-4′), 7.96 (2H, d, 7.8 Hz, H-5′), 7.46 (2H, dt, 7.8 Hz, 0.9 Hz, H-6’…, 4488-22-6

The synthetic route of 4488-22-6 has been constantly updated, and we look forward to future research findings.

Reference£º
Article; Mikle, Gbor; Boros, Borbla; Kollr, Lszl; Tetrahedron Asymmetry; vol. 25; 23; (2014); p. 1527 – 1531;,
Chiral Catalysts
Chiral catalysts – SlideShare

A common heterocyclic compound, the chiral-catalyst compound, name is trans-Cyclohexane-1,2-diamine,cas is 1121-22-8, mainly used in chemical industry, its synthesis route is as follows.,1121-22-8

General procedure: Salen ligands were obtained in the stoichiometric reaction of salicylic aldehyde and trans-1,2-diaminocyclohexane in 96% ethanol solution according to [13c]. Reactions were carried out in 50 ml three-neck round-bottomed flask, equipped with reflux condenser, dropping funnel, magnetic stirrer and heating mantle. The solution of trans-1,2-diaminocyclohexane (0,57 ml, 5 mmol) in EtOH (10 ml) was slowly added to a hot solution of appropriate aldehyde (10 mmol) in EtOH (20 ml). The reaction mixture was heated at reflux for 1.5 h. After cooling to room temperature, the yellow precipitate that formed was filtered off and washed with cold EtOH (5 ml). The ligands were used without further purification. (¡À)-trans-N,N-bis(5-methoxy-3-tert-butylsalicylidene)-1,2-cyclohexanediamine (H2salcn(BuOMe)) Anal. Calc. for C30H42N2O2: C, 72.84%; H, 8.56%; N, 5.66%; C/N = 12.87. Found: C, 72.63%; H, 8.45%; N, 5.68%; C/N = 12.78. 1H-NMR (CDCl3): delta = 13.40 (bs, 2H), 8.24 (s, 2H), 6.90 (m, 2H), 6.48 (m,2H), 3.69 (s, 6H), 3.32 (m, 2H), 1.99 (m, 2H), 1.89 (m, 2H), 1.77 (m, 2H), 1.47 (m, 2H), 1.39 (s, 18H). Yield: 1.33 g, 54%, mp = 146-149 C.

As the rapid development of chemical substances, we look forward to future research findings about 1121-22-8

Reference£º
Article; Tomczyk; Nowak; Bukowski; Bester; Urbaniak; Andrijewski; Olejniczak; Electrochimica Acta; vol. 121; (2014); p. 64 – 77;,
Chiral Catalysts
Chiral catalysts – SlideShare

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.673-06-3,D-Phenylalanine,as a common compound, the synthetic route is as follows.

673-06-3, EMBODIMENT 1 N-(BENZYLOXYCARBONYL)-D-PHENYLALANINE A 15.0 g sample of D-phenylalanine was dissolved in 45 ml of aqueous solution containing 7.26 g of 50% sodium hydroxide. This solution was stirred at 0-10 C. as 16.3 g of benzyl chloroformate was added rapidly in portions. The resulting reaction was mildly exothermic, and shortly after addition, solids precipitated. An additional 45 ml of water and 3.63 g of 50% sodium hydroxide were added, causing most of the solids to redissolve. The reaction mixture was stirred for 20 minutes and then acidified with 6 N hydrochloric acid. The resulting solids were filtered, washed with water and then with hexane, and dried by suction and then under vacuum to give 47 g of white solids. These solids dissolved in ether were washed twice with 1 N hydrochloric acid and then with water, dried over MgSO4 and stripped to 35 C. at 2.5 mm Hg to give 27.7 g of the desired product as a colorless oil.

673-06-3 D-Phenylalanine 71567, achiral-catalyst compound, is more and more widely used in various fields.

Reference£º
Patent; Shell Oil Company; US4594196; (1986); A;,
Chiral Catalysts
Chiral catalysts – SlideShare

trans-Cyclohexane-1,2-diamine, cas is 1121-22-8, it is a common heterocyclic compound, the chiral-catalyst compound, its synthesis route is as follows.,1121-22-8

General procedure: A methanolic solution (10mL) of (¡À)-trans-1,2-diaminocyclohexane (dach) (0.23g, 2.0mmol) in a Schlenk tube, was added dropwise to a methanolic solution (20mL) of salicylaldehyde-imidazolium salt H(iPr)sal(Me2Im+-X-) 3a-c (4.0mmol) into a 100mL Schlenk flask under nitrogen atmosphere. The reaction mixture was stirred under N2 at 60C for 3h. Then the solvent was partially removed under reduced pressure, and the yellow products of 4a-c were precipitated by the addition of ethyl acetate and kept in the refrigerator overnight. Solvent was decanted off and the obtained crude product was sonicated for 15min in Et2O (3¡Á25mL). Et2O was also decanted off and the residual solid was washed intensively with MeOH/Et2O mixture (1:2) to remove unreacted materials and then re-dissolved in MeOH. EtOAc was added slowly (?15min) to precipitate the products as pale yellow-dark orange solids which were collected by filtration and dried under vacuum. Samples of the isolated solids were characterized as follows.

As the rapid development of chemical substances, we look forward to future research findings about 1121-22-8

Reference£º
Article; Elshaarawy, Reda F.M.; Kheiralla, Zeinab H.; Rushdy, Abeer A.; Janiak, Christoph; Inorganica Chimica Acta; vol. 421; (2014); p. 110 – 122;,
Chiral Catalysts
Chiral catalysts – SlideShare

173035-10-4, 1,3-Dimesityl-4,5-dihydro-1H-imidazol-3-ium chloride is a chiral-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

Complex 1e was synthesized similarly as reported for the(5-C5Me5) complex by Ritleng et al. [4e]. A hexane solution ofn-BuLi (2.5 mL, 5.1 mmol) was added to a THF (5 mL) solution of1,3-bis(1,1-dimethylbut-3-enyl)cyclopentadiene (4.83 mmol). Theresulting mixture was stirred for 2 h at ambient temperature. Thissolution was added to a solution of [Ni(acac)2] (1.199 g, 4.67 mmol)in THF (10 mL) at -78C. The color changed immediately fromgreen to red and a suspension of 1,3-dimesitylimidazolinium chlo-ride [12] (1.693 g, 4.96 mmol) in THF (10 mL) was quickly added atthis temperature. The reaction mixture was allowed to warm up to ambient temperature and stirred for a further 2 h. The volatileswere removed under reduced pressure. The solid residue wasextracted with hexane (20 mL) and filtered through Celite. Com-plex 1e was isolated by crystallization as a red, microcrystallinesolid. Yield: 2.40 g (3.82 mmol, 79%).1H NMR (CDCl3, 400 MHz) (ppm) = 7.04 (s, 4H, Ar), 5.51-5.62 (m, 2H, CH ), 4.88-4.90 (m,4H, CH2), 4.14 (s, 1H, C5H3), 3.82 (s, 4H, NCH2), 3.62 (s, 2H,C5H3), 2.37 (s, 12H, o-CH3), 2.35 (s, 6H, p-CH3), 2.01 (m, 2H, CH2),1.84 (m, 2H, CH2), 0.85 (s, 6H, CH3), 0.71 (s, 6H, CH3).13C{1H}NMR (CDCl3, 101 MHz) (ppm) = 204.0 (NCN), 138.3 ( CH ) 137.8,137.2, 136.4, 132.1, 129.9 (Ar and C5H3), 116.1 ( CH2), 91.2 (C5H3),76.5 (C5H3), 51.25 (NCH2), 49.00 (CH2), 33.40 (C(CH3)2), 28.84,26.39 (CH3), 21.02, 18.80 (o- and p-CH3). MS (EI, 70 eV) m/z (rel.int.%) (58Ni) 628 (M+, 10), 516 (M+-C8H16, 26), 361 (M+-C20H27,100). HRMS (EI) for C38H51N235Cl58Ni: calc. 628.30942, found628.30983. C38H51N2ClNi Calc. (%) C 72.45, H 8.15, N 4.44, foundC 72.41, H 8.08, N 4.38. Crystals suitable for X-ray measurementwere grown from a concentrated solution in n-heptane/THF at 4C., 173035-10-4

173035-10-4 1,3-Dimesityl-4,5-dihydro-1H-imidazol-3-ium chloride 2734917, achiral-catalyst compound, is more and more widely used in various fields.

Reference£º
Article; Buchowicz, W?odzimierz; Conder, Joanna; Hryciuk, Dymitr; Zachara, Janusz; Journal of Molecular Catalysis A: Chemical; vol. 381; (2014); p. 16 – 20;,
Chiral Catalysts
Chiral catalysts – SlideShare

D-Phenylalanine, cas is 673-06-3, it is a common heterocyclic compound, the chiral-catalyst compound, its synthesis route is as follows.,673-06-3

In a 3 1 jacketed reactor equipped with mechanical stirring and thermometer, 48% HBr (1,224.6 g, 7.265 moles), demineralized water (450 ml) and toluene (504 ml) were charged at 15C under nitrogen flow. The mixture temperature was brought to 0C and (D)-phenylalanine (300 g, 1.816 moles) was added. The mixture was then cooled to inner -5C and, in 5 hours, a solution of sodium nitrite (162.9 g, 2.361 moles) in demineralized water (306 ml) was dropped therein, keeping the temperature between -4C and -6C. After 3 hours the reaction temperature was brought to 15C and the stirring was kept on for another hour, then the reaction mixture was left to stand for half of hour, the nitrogen flow was stopped and the phases were separated. The organic phase was added with toluene (800 g, 924 ml) and demineralized water (450 g). The mixture was stirred for 1 hour, left to stand for half of hour, and the phases separated. The organic one was concentrated to dryness under vacuum in thermostated bath at 50C. There were thus obtained 385.8 g (1.684 moles) of (R)-2-bromo-3-phenyl-propionic acid (yield: 92.7%).

With the rapid development of chemical substances, we look forward to future research findings about D-Phenylalanine

Reference£º
Patent; ZAMBON GROUP S.p.A.; EP1056707; (2004); B1;,
Chiral Catalysts
Chiral catalysts – SlideShare

4488-22-6, [1,1′-Binaphthalene]-2,2′-diamine is a chiral-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

(1) Synthesis of N,N’-di-p-toluenesulfonyl-1,1′-binaphthyl-2,2′-diamine Under nitrogen atmosphere, to a solution in which 1,1′-binaphthyl-2,2′-diamine (0.5 mmol) was dissolved in pyridine (1 mL) was added p-toluenesulfonyl chloride (1.1 mmol) at room temperature, and the mixture was reacted for 5 to 12 hours with stirring. After completion of the reaction, the resulting red suspension was diluted with ethyl acetate, and back-extracted with 1N hydrochloric acid to remove pyridine. The resulting organic layer was dried with sodium sulfate to remove the solvent, and the residue was purified by column chromatography to obtain an objective substance as a pale yellow to white solid in more than 95% yield.

4488-22-6, Big data shows that 4488-22-6 is playing an increasingly important role.

Reference£º
Patent; Terada, Masahiro; Uraguchi, Daisuke; Sorimachi, Keiichi; Shimizu, Hideo; US2007/142639; (2007); A1;,
Chiral Catalysts
Chiral catalysts – SlideShare

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.1121-22-8,trans-Cyclohexane-1,2-diamine,as a common compound, the synthetic route is as follows.

General procedure: 2.6.2 ;(alphaR,3aR,7aR)-rel-2-(1-hydroxyethyl)-3a,4,5,6,7,7a-Hexahydro-1H-benzimidazole (2); In a typical catalytic reaction, 1.1 mmol of glycerol dissolved in6.0 ml of water were introduced in a Schlenk tube equipped withan argon inlet and deaerated by bubbling argon through a needlefor 15 min. After addition of the catalyst (0.011 mmol) and of thecocatalyst (0.11 mmol), the reaction vessel was closed with a serumcap serumcap and the amine (1.1 mmol) was added by a micro-syringe; thenthe vessel was heated under vigorous stirring to the chosen reactiontemperature in a thermostatted oil bath. After the desired reactiontime, the catalytic reaction was stopped by cooling the Schlenk tubeto r.t. and letting air in under stirring.

1121-22-8, The synthetic route of 1121-22-8 has been constantly updated, and we look forward to future research findings.

Reference£º
Article; Crotti, Corrado; Farnetti, Erica; Licen, Sabina; Barbieri, Pierluigi; Pitacco, Giuliana; Journal of Molecular Catalysis A: Chemical; vol. 382; (2014); p. 64 – 70;,
Chiral Catalysts
Chiral catalysts – SlideShare

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.4488-22-6,[1,1′-Binaphthalene]-2,2′-diamine,as a common compound, the synthetic route is as follows.

Under nitrogen conditions, add tris (dibenzylidene-base acetone) dipalladium (37 mg, 0.04 mmol, purchased from ANEG) to Schlenk bottles with magnetons, 1,1′-Binaphthyl-2,2′-bisdiphenylphosphine (50 mg, 0.08 mmol, purchased from Anagi), cesium carbonate (3.65 g, 11.2 mmol, purchased from Anagi), 2-trifluoromethanesulfonyl cycloheptatrienone (4.88 g, 19.2 mmol), 1,1′-bi-2-naphthylamine (2.27 g, 8 mmol, purchased from Enagi) and 50 ml of toluene. The resulting mixture was stirred at 100 C for 24 hours. The reaction was completed and the temperature was reduced to room temperature. After the toluene-insoluble solid was filtered off with diatomaceous earth, 100 mesh silica gel was added to the resulting solution to spin dry the sample. The obtained crude product was then passed through a 200-300 mesh silica gel column, using ethyl acetate as an eluent, and the eluent was spin-dried to obtain a brown solid (2.68 g, yield 68%)., 4488-22-6

The synthetic route of 4488-22-6 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; University of Science and Technology of China; Chen Changle; Zhang Pan; (17 pag.)CN110423246; (2019); A;,
Chiral Catalysts
Chiral catalysts – SlideShare