Category: chiral-catalyst

673-06-3, D-Phenylalanine is a chiral-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

General procedure: Both L- and D-alpha-bromo-phenylalanine were synthesized using 1.6 eq sodium nitrite in a 48% HBr/H 2 O solution as described by Baidola et. al 9 . L-alpha-bromo-tryptophan and DL-1-alpha-bromo-naphthylalanine were both synthesized with 1.9 eq sodium nitrite and 3.7 eq KBr in 4.4 eq 0.75M HBr as defined by Souers et. al 1 . Additional information regarding synthesis is given below., 673-06-3

As the paragraph descriping shows that 673-06-3 is playing an increasingly important role.

Reference£º
Article; Samuels, Eric R.; Sevrioukova, Irina F.; Tetrahedron Letters; vol. 59; 12; (2018); p. 1140 – 1142;,
Chiral Catalysts
Chiral catalysts – SlideShare

trans-Cyclohexane-1,2-diamine, cas is 1121-22-8, it is a common heterocyclic compound, the chiral-catalyst compound, its synthesis route is as follows.,1121-22-8

First, 5.84g of benzyl (manufactured by Tokyo Kasei Kogyo Co., Ltd) was mixed with 3.17g of trans- 1,2-cyclohexanediamine (manufactured by Kanto Kagaku) by using 150 mL of ethanol as a solvent. Then, the mixed solution was refluxed for 3 hours at 500C. After that, the refluxed solution was cooled to be a room temperature. A deposit was obtained by filtering the refluxed solution. After that, 2,3-diphenyl-4a,5,6,7,8,8a-hexahydroquinoxaline was obtained by recrystallizing the deposit with ethanol (light yellow crystal, yield: 96%). Subsequently, 7.66g of 2,3-diphenyl-4a,5,6,7,8,8a-hexahydroquinoxaline, which was obtained in the above step, was mixed with 8.62g of iron chloride (III) by using 80 mL of ethanol as a solvent. Then the mixed solution was gently stirred with heat for 3 hours. After the stirring, a ligand 2,3-diphenyl-5,6,7,8-tetrahydroquinoxaline (abbreviation: DPQtH) was obtained by adding water (milky white powder, tield: 88%).

With the rapid development of chemical substances, we look forward to future research findings about 1121-22-8

Reference£º
Patent; SEMICONDUCTOR ENERGY LABORATORY CO., LTD.; WO2006/104177; (2006); A1;,
Chiral Catalysts
Chiral catalysts – SlideShare

602-09-5, [1,1′-Binaphthalene]-2,2′-diol is a chiral-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

602-09-5, A 300mL eggplant-shaped flask, the raw material 1,1′-bi-2-naphthol (5.4g, 19mmol), Zeolyst Co. weighed Zeolith the CBV780 (2.5g), was suspended was added o- dichlorobenzene (30mL). After the suspension was heated to reflux 18 hours, heating was filtered, washed with toluene column. After concentrating the filtrate to approximately o- dichlorobenzene are others, was precipitated by adding methanol. The resultant solid was filtered to give the intermediate 7 as a white powder (4.6g, 18mmol, 90%). It was identified as the desired compound by FDMS (field desorption mass analysis).

The synthetic route of 602-09-5 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; Idemitsu Kosan Corporation; Ikeda, Yoichi; Ito, Hirokazu; Kawamura, Masahiro; Saito, Hiroyuki; Ikeda, Takeshi; (125 pag.)KR2015/98631; (2015); A;,
Chiral Catalysts
Chiral catalysts – SlideShare

trans-Cyclohexane-1,2-diamine, cas is 1121-22-8, it is a common heterocyclic compound, the chiral-catalyst compound, its synthesis route is as follows.,1121-22-8

General procedure: A methanolic solution (10mL) of (¡À)-trans-1,2-diaminocyclohexane (dach) (0.23g, 2.0mmol) in a Schlenk tube, was added dropwise to a methanolic solution (20mL) of salicylaldehyde-imidazolium salt H(iPr)sal(Me2Im+-X-) 3a-c (4.0mmol) into a 100mL Schlenk flask under nitrogen atmosphere. The reaction mixture was stirred under N2 at 60C for 3h. Then the solvent was partially removed under reduced pressure, and the yellow products of 4a-c were precipitated by the addition of ethyl acetate and kept in the refrigerator overnight. Solvent was decanted off and the obtained crude product was sonicated for 15min in Et2O (3¡Á25mL). Et2O was also decanted off and the residual solid was washed intensively with MeOH/Et2O mixture (1:2) to remove unreacted materials and then re-dissolved in MeOH. EtOAc was added slowly (?15min) to precipitate the products as pale yellow-dark orange solids which were collected by filtration and dried under vacuum. Samples of the isolated solids were characterized as follows.

With the rapid development of chemical substances, we look forward to future research findings about 1121-22-8

Reference£º
Article; Elshaarawy, Reda F.M.; Kheiralla, Zeinab H.; Rushdy, Abeer A.; Janiak, Christoph; Inorganica Chimica Acta; vol. 421; (2014); p. 110 – 122;,
Chiral Catalysts
Chiral catalysts – SlideShare

673-06-3, D-Phenylalanine is a chiral-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

673-06-3, General procedure: Amino acid or peptide (1 mmol) was added with stirring to a solution of guanidine hydrochloride (15 mol%) and di-tert-butyl dicarbonate (2.5-3 mmol) in EtOH (1 mL), at 35-40C. The reaction mixture was continued to stir until a clear solution was obtained. EtOH was evaporated under vacuum and the residue was successively washed with water (2 mL) and hexane or petroleum ether (2 mL) to afford almost pure N-Boc amino acids or N-Boc peptides. If necessary, the crude products could be recrystallized for further purification.

As the paragraph descriping shows that 673-06-3 is playing an increasingly important role.

Reference£º
Article; Jahani, Fatemeh; Tajbakhsh, Mahmood; Golchoubian, Hamid; Khaksar, Samad; Tetrahedron Letters; vol. 52; 12; (2011); p. 1260 – 1264;,
Chiral Catalysts
Chiral catalysts – SlideShare

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.1121-22-8,trans-Cyclohexane-1,2-diamine,as a common compound, the synthetic route is as follows.

Into a solution containing 1,12-diisocyanatododecane (5.04 grams, 20 mmol; obtained from Sigma-Aldrich Fine Chemicals) and a 1:1 mixture of hexane and tetrahydrofuran (75 milliliters) stirring at room temperature was added a solution containing triethylene glycol monomethacrylate (4.36 grams, 20 mmol; obtained as CD570 from Sartomer Company Inc., Exton, Pa.) dissolved in a 1:1 mixture of hexane and tetrahydrofuran (25 milliliters), and dibutyltin dilaurate (0.063 grams, 0.1 mmol; obtained from Sigma-Aldrich Fine Chemicals) as the catalyst. The mixture was stirred and heated to an internal temperature of 40 C. The progress of the reaction was monitored by 1H-NMR spectroscopy for consumption of the triethylene glycol monomethacrylate reactant. The mixture was cooled to about 15 C. temperature, after which to this mixture was added dropwise a solution of trans-1,2-diaminocyclohexane (1.14 grams, 10 mmol; obtained as a racemic mixture of (1R,2R) and (1S,2S) stereoisomers from Sigma-Aldrich Fine Chemicals) dissolved in a 1:1 mixture of hexane and tetrahydrofuran (20 milliliters). The reaction mixture was stirred for 1 hour while warming up to room temperature. FTIR spectroscopic analysis of a reaction sample showed little unreacted isocyanate (peak at 2180 cm-1, sample prepared as a KBr pellet). Any residual isocyanate reagent was quenched by addition of methanol (5 milliliters), The reaction mixture was then filtered by vacuum filtration to give 10.11 grams of a solid product as a white powder (96 percent yield). The product was believed to be of the formulae 1H-NMR spectroscopic analysis of the solid was performed in DMSO-d6 (300 MHz) at room temperature (25 C.) and indicated the above structure with the following assigned peaks: 1.10-1.80 ppm (multiplet, 24 H integration, 20 protons from -NH-CH2(CH2)10CH2-NH- portion and 4 methylene protons from the cyclohexane ring portion); 1.90 ppm (singlet, 3 H integration, -(CO)C(CH3)CH2); 2.95 ppm (narrow multiplet, 4 H integration, -NH-CH2(CH2)10CH2-NH-); 3.35 ppm (multiplet, 1 H, cyclohexane ring methine proton); 3.55 ppm (narrow multiplet, 8 H integration, -(CH2-O) protons); 4.07 ppm and 4.27 ppm (broad singlets, each 2 H integration, NH(CO)OCH2CH2O- and -OCH2CH2O(CO)-C(CH3)CH2); 5.70 ppm and 5.88 ppm (broad singlet, each 1 H integration, urea NH protons); 5.70 ppm and 6.18 ppm (sharp singlet, each 1 H integration, terminal vinyl protons -(CO)C(CH3)CH2); 7.15 ppm (broad singlet, 1 H integration, urethane NH proton). Elemental analysis calculated for: C: 57.80%, H: 8.80%, N: 8.99%. Found for: C: 61.39%, H: 9.28%, N: 7.96%.

1121-22-8, As the paragraph descriping shows that 1121-22-8 is playing an increasingly important role.

Reference£º
Patent; Xerox Corporation; US2006/122415; (2006); A1;,
Chiral Catalysts
Chiral catalysts – SlideShare

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.4488-22-6,[1,1′-Binaphthalene]-2,2′-diamine,as a common compound, the synthetic route is as follows.

To a solution of BINAM (100 mg, 0.35 mmol) and pyridine (85 mL, 1.05 mmol) inacetnitrile (3.5 mL) was added p-toluenesulfonylchloride (73 mg, 0.38 mmol), and the mixture was refluxed for 12 h. After cooling to ambient temperature, the reaction was quenched with brine (10 mL) and extracted with EtOAc (15 mL¡Á 3). The combined organic extracts were dried (MgSO4) and concentrated. The residue was purifiedby column chromatography on silica gel using hexane-EtOAc as the eluent, to give A-2; yield: 119 mg (78%)., 4488-22-6

The synthetic route of 4488-22-6 has been constantly updated, and we look forward to future research findings.

Reference£º
Article; Zhang, Yu; Mao, Mao; Ji, Yi-Gang; Zhu, Jie; Wu, Lei; Tetrahedron Letters; vol. 57; 3; (2016); p. 329 – 332;,
Chiral Catalysts
Chiral catalysts – SlideShare

[1,1′-Binaphthalene]-2,2′-diol, cas is 602-09-5, it is a common heterocyclic compound, the chiral-catalyst compound, its synthesis route is as follows.,602-09-5

Add 22.88 g (80 mmol) of binaphthol to 100 mL of acetic acid and 100 mL of CH 2 Cl 2 solution, and add 6.8 mL (160.4 mmol) of fuming HNO3 in an ice bath, and stir at room temperature overnight.TLC detects the formation of new substances and pours the product into ice water for filtration.The solid was washed with CH 2 Cl 2 and methanol.TLC is detected as a point, vacuum dried,The product a6,6′-dinitro(1,1′-binaphthyl-2,2′) diol was obtained.

With the rapid development of chemical substances, we look forward to future research findings about 602-09-5

Reference£º
Patent; East China Normal University; Liu Qiancai; Ma Junyi; Tao Xuewei; An Shujie; Tang Guofeng; (12 pag.)CN109810124; (2019); A;,
Chiral Catalysts
Chiral catalysts – SlideShare

[1,1′-Binaphthalene]-2,2′-diamine, cas is 4488-22-6, it is a common heterocyclic compound, the chiral-catalyst compound, its synthesis route is as follows.,4488-22-6

Preparation of ligands.; Synthesis of imines.; 3 mmol of bisnaphthyldiamine and 6 mmol of ketone were dissolved in 30 mL of anhydrous toluene. A few mg of para toluene sulfonic acid were added. After addition of 30 g of activated 4 angstroem molecular sieves by 10 g portions, the reaction mixture was stirred at a temperature of 110C for a period of time of 3 days. Molecular sieves were filtered off and the solvent was removed under vacuum. The resulting solid was crystallised from methanol to give the product. Two compounds were obtained and characterised. Bis-naphthyldi(phenylmethyleneimine) was obtained as a yellow solid with a yield of 79 %. [Show Image] The NMR results were as follows. 1H-RMN (300 MHz, CD2Cl2) [Show Image] (ppm) : 6.64 (d, 2H), 6.7-4-78 (m, 8H), 6.93-6.97 (m, 4H), 7.05 (t, 2H), 7.19-7.48 (m, 6H), 7.50 (t, 2H), 7.68 (d, 6H), 7.77 (d, 2H) 13C-RMN (75 MHz, CD2Cl2) [Show Image] (ppm) : 122.2, 124.1, 124.2, 126.1, 126.5, 127.8, 127.9, 128.0, 128.2, 128.3, 128.9, 130.0, 130.2, 130.6, 130.7, 133.9, 136.6, 140.8, 147.6, 167.2

With the rapid development of chemical substances, we look forward to future research findings about 4488-22-6

Reference£º
Patent; TOTAL PETROCHEMICALS RESEARCH FELUY; EP1982975; (2008); A1;,
Chiral Catalysts
Chiral catalysts – SlideShare

1121-22-8, trans-Cyclohexane-1,2-diamine is a chiral-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

Paraformaldehyde (0.32 g) was mixed with N,N-dimethylformamide (1.92 g) and heated to 80 C to make a slurry. (¡À)-trans-1,2-Cyclohexanediamine (2) (Aldrich 270016) (0.53 g) was added to the slurry, where upon the mixture turned orange. The mixture was heated for 0.5 h at 80 C, then cooled and left for one week. The mixture was filtered and the crystals washed with ethanol to afford the 1,8,10,17-tetraazapentacyclo[8.8.1.18,17.02,7.011,16]icosane (4) (0.46 g; 71%). The product was recrystalised from a mixture of 1 part petroleum ether, 2 parts hexanes and 1.3 parts ethyl acetate (by volume; total volume 21.5 mL). Insoluble material was removed by filtration and the filtrate left to crystallize to afford off-white prisms (67% recovery), m.p. 210 C., 1121-22-8

1121-22-8 trans-Cyclohexane-1,2-diamine 43806, achiral-catalyst compound, is more and more widely used in various fields.

Reference£º
Article; Hendsbee, Arthur; Vaughan, Keith; Journal of Molecular Structure; vol. 1050; (2013); p. 1 – 4;,
Chiral Catalysts
Chiral catalysts – SlideShare