Tag: M.W:100-200

As a common heterocyclic compound, it belongs to quinuclidine compound,Quinuclidine-4-carboxylic acid hydrochloride,40117-63-3,Molecular formula: C8H14ClNO11,mainly used in chemical industry, its synthesis route is as follows.,1121-22-8

Into a solution containing 1,6-diisocyanatohexane (4.04 grams, 24.0 mmol; obtained from Sigma-Aldrich Fine Chemicals) and anhydrous tetrahydrofuran (100 mL, obtained from Sigma-Aldrich Fine Chemicals) stirring at room temperature was added 1-octanol (3.13 grams, 24.0 mmol, obtained from Sigma-Aldrich Fine Chemicals) and dibutyltin dilaurate (0.15 grams, 0.24 mmol, obtained from Sigma-Aldrich Fine Chemicals) as the catalyst. The mixture was stirred and heated to an internal temperature of about 65 C. The progress of the reaction was monitored by 1H-NMR spectroscopy for the consumption of 1-octanol starting material, indicated by the disappearance of the -CH2OH multiplet, which appears at 3.6 ppm downfield of the intermediate isocyanate product whose signal is located at 3.35 ppm. The mixture was cooled to about 15 C. internal temperature; thereafter, to this mixture was added dropwise a solution of trans-1,2-diaminocyclohexane (1.37 grams, 12 mmol; obtained as a racemic mixture of (1R,2R) and (1S,2S) stereoisomers from Sigma-Aldrich Fine Chemicals) dissolved in anhydrous tetrahydrofuran (10 mL). The mixture was stirred for about 60 minutes while warming up to room temperature, and thickened to form a gelatinous slurry. FTIR spectroscopic analysis of a reaction sample showed very little unreacted isocyanate (peak at 2180 cm-1, sample prepared as a KBr pellet). Residual isocyanate was quenched by addition of 5 mL of methanol. A crystalline product was isolated from the slurry by first adding diethyl ether (20 mL) followed with stirring for approximately 30 minutes to ensure full precipitation out of the gel slurry. The solid was filtered by suction on a paper filter, rinsed with diethyl ether, and then dried in air to give 6.20 grams of off-white solid (77.5% yield). The product was believed to be of the formulae 1H-NMR spectroscopic analysis of the solid was performed in DMSO-d6 (300 MHz) at high temperature (60 C.) and indicated the above structure with the following assigned peaks: 0.90 ppm (multiplet, 3 H integration, -OCH2(CH2)6CH3); 1.05-1.95 ppm (broad multiplets, 24 H integration, 12 methylene protons from 2-ethylhexanol portion, 8 methylene protons from the 1,6-diisocyanatohexane portion, and 4 methylene protons from the cyclohexane ring portion); 2.95 ppm (narrow multiplet, 4 H integration, -NH(CO)NHCH2(CH2)4CH2NH(CO)O); 3.35 ppm (doublet, 1 H integration, tertiary methine proton adjacent to urea group on cyclohexane ring); 3.90 ppm (doublet of doublets, 2 H integration, NH(CO)OCH2(CH2)6CH3; 5.70 ppm and 5.85 ppm (each a broad singlet, 1 H integration, urea NH protons); 7.00 ppm (broad singlet, 1 H integration, urethane NH proton). Elemental analysis calculated for C: 64.19%, H: 10.49%, N: 11.82%; found for C: 64.46%, H: 10.63%, N: 10.69%.

With the synthetic route has been constantly updated, we look forward to future research findings about trans-Cyclohexane-1,2-diamine,belong chiral-catalyst compound

Reference£º
Patent; Xerox Corporation; US2006/122415; (2006); A1;,
Chiral Catalysts
Chiral catalysts – SlideShare

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.673-06-3,D-Phenylalanine,as a common compound, the synthetic route is as follows.

673-06-3, General procedure: The amino acid of configuration (R)- (39.3 mmol) is solubilized in 50 ml of water. At 0 C., KBr (3.5 eq, 31.8 g) and then H2SO4 (7.73 ml), respectively, are added dropwise, while maintaining the temperature below 5 C. The mixture is cooled to -10 C. and NaNO2 (1.3 eq, 3.59 g) solubilized in 17 ml of water is added dropwise. The mixture is stirred for 2 hours at -5 C. (0196) After returning to room temperature, the mixture is extracted with CH2Cl2 (2¡Á50 ml). The organic phase is washed with H2O, saturated NaCl, dried on Na2SO4 to yield the expected product of configuration (R). (0197) 3a R2=CH2Ph: light yellow oil; (Yield: 50%); Rf (CH2Cl2/MeOH): 0.62 (0198) NMR (CDCl3, 200 MHz): 3.15-3.40 (2H, dd); 4.69 (1H, m); 7.20-7.40 (5H, m)

673-06-3 D-Phenylalanine 71567, achiral-catalyst compound, is more and more widely used in various fields.

Reference£º
Patent; PHARMALEADS; ROQUES, Bernard Pierre; FOURNIE-ZALUSKI, Marie-Claude; PORAS, Herve; US2015/299116; (2015); A1;,
Chiral Catalysts
Chiral catalysts – SlideShare

As a common heterocyclic compound, it belong chiral-catalyst compound,(S)-Azetidine-2-carboxylic acid,2133-34-8,Molecular formula: C4H7NO2,mainly used in chemical industry, its synthesis route is as follows.,2133-34-8

Synthesis of Azethidine-2-carboxylic Acid N-carboxyamino Acid Anhydride At room temperature, (S)-azethidine-2-carboxylic acid (1.0 g, 99.9% ee or higher) was suspended in 25 ml of tetrahydrofuran. Then tri-phosgene (1.0 g) was added thereto. The suspension was heated to 50 C. and stirred for 4 hours. After allowing to cool, the solvent was distilled off under reduced pressure to give a pale yellow oil (1.5 g). 1H-NMR(CDC13) delta 4.52 (dd, 1H), 3.76-3.62 (m, 2H), 2.44-2.36 (m, 1H), 2.23-2.14 (m, 1H), 13C-NMR (CDC13) delta 169.10, 152.27, 55.44, 40.37, 34.22.

With the synthetic route has been constantly updated, we look forward to future research findings about (S)-Azetidine-2-carboxylic acid,belong chiral-catalyst compound

Reference£º
Patent; Matsuo, Kazuhiko; Tsukuya, Kentaro; US2002/151721; (2002); A1;,
Chiral Catalysts
Chiral catalysts – SlideShare

1121-22-8, trans-Cyclohexane-1,2-diamine is a chiral-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

Into a solution containing 1,6-diisocyanatohexane (2.35 grams, 13.95 mmol; obtained from Sigma-Aldrich Fine Chemicals) and anhydrous hexane (100 mL, obtained from Sigma-Aldrich Fine Chemicals) stirring at room temperature was added diethylene glycol butyl ether (2.27 grams, 14.0 mmol, obtained from Sigma-Aldrich Fine Chemicals), which was previously dried over calcium chloride granules, and dibutyltin dilaurate as catalyst (0.095 grams, 0.15 mmol, obtained from Sigma-Aldrich Fine Chemicals). The mixture was stirred and heated to an internal temperature of about 45 C. The progress of the reaction was monitored by 1H-NMR spectroscopy for the consumption of the diethylene glycol butyl ether starting material. The mixture was cooled to about 15 C. internal temperature; thereafter, to this mixture was added dropwise a solution of trans-1,2-diaminocyclohexane (0.80 grams, 7.0 mmol; obtained as a racemic mixture of (1R,2R and (1S,2S) stereoisomers from Sigma-Aldrich Fine Chemicals) dissolved in anhydrous hexane (20 mL). The mixture was stirred for about 30 minutes while warming up to room temperature, and FTIR spectroscopic analysis of a reaction sample indicated no unreacted isocyanate (peak at 2180 cm-1, sample prepared as a KBr pellet). The crystalline product was isolated by vacuum filtration on filter paper, rinsed with hexane, and then dried in air to give 4.82 grams of a white powder (88.8% yield). The product was believed to be of the formulae 1H-NMR spectroscopic analysis of the solid was performed in DMSO-d6 (300 MHz) at 80 C. and indicated the above structure with the following assigned peaks: 0.90 ppm (multiplet, 3 H integration, -OCH2CH2OCH2CH2OCH2CH2CH2CH3); 1.05-1.95 ppm (broad multiplets, 16 H integration, 4 methylene protons from butyl ether terminus, 8 methylene protons from the 1,6-diisocyanatohexane portion, and 4 methylene protons from the cyclohexane ring portion); 3.0 ppm (narrow multiplet, 5 H integration, -NH(CO)NHCH2(CH2)4CH2NH(CO)O and also tertiary methine proton adjacent to urea group on cyclohexane ring); 3.40-3.70 ppm (multiplets, 8 H integration, NH(CO)OCH2CH2OCH2CH2OCH2CH2CH2CH3); 4.10 ppm (singlet, 2 H integration, NH(CO)OCH2CH2OCH2CH2OCH2CH2CH2CH3); 5.60 ppm and 5.70 ppm (each a broad singlet, 1 H integration, urea NH protons); 6.75 ppm (broad singlet, 1 H integration, urethane NH proton). Elemental analysis calculated for C: 58.83%, H: 9.54%, N: 10.83%; found for C: 58.81%, H: 9.58%, N: 12.17%.

1121-22-8, 1121-22-8 trans-Cyclohexane-1,2-diamine 43806, achiral-catalyst compound, is more and more widely used in various fields.

Reference£º
Patent; Xerox Corporation; US2006/122415; (2006); A1;,
Chiral Catalysts
Chiral catalysts – SlideShare

Name is trans-Cyclohexane-1,2-diamine, as a common heterocyclic compound, it belongs to chiral-catalyst compound, and cas is 1121-22-8, its synthesis route is as follows.,1121-22-8

A 10 mL sample solution containing 1.0 mg/L of trans-cyclohexane-1,2-diamine was placed in a centrifuge tube with narrow neck (~4 mm i.d.), which was specially designed for ease of removing the supernatant phase. A mixture of 1 mL disperser solvent and 300 muL extracting solvent with 2 mmol L-1 of chiral selector was rapidly injected into the sample solution using a 5.0 mL syringe, and mixed by vortex mixer at 500 rpm stirring rate for 20 min, so that a cloudy solution was formed. The cloudy solution was centrifuged for 5 min at 3500 rpm, and the extraction product (supernatant phase) was collected in the neck of the tube. Finally, this supernatant phase was derivatized and injected into the HPLC. All of the experiments were carried out in triplicate and the average of the result was reported.

With the complex challenges of chemical substances, we look forward to future research findings about trans-Cyclohexane-1,2-diamine

Reference£º
Article; Hashemi, Majid; Hadjmohammadi, Mohammad Reza; Tetrahedron Asymmetry; vol. 28; 3; (2017); p. 454 – 459;,
Chiral Catalysts
Chiral catalysts – SlideShare

22795-99-9, (S)-(1-Ethylpyrrolidin-2-yl)methanamine is a chiral-catalyst compound, ?involved in a variety of chemical synthesis. Rlated chemical reaction is continuously updated

22795-99-9, Example 43 Synthesis of N2-cyclohexylmethyl-N4-((S)-1-ethyl-pyrrolidin-2-ylmethyl)-N6-(3-fluoro-4-methoxphenyl)-1,3,5-triazine-2,4,6-triamine (141) To a mixture of cyanuric chloride (0.368 g, 2 mmol) in CH3CN at about -20¡ã C. was added 3-fluoro-p-anisidine (0.28 g, 2 mmol) in CH3CN followed by the addition of N,N-diisopropylethylamine (DIEA) (0.35 mL, 2 mmol) and stirred for about 1 hour. The reaction mixture was then stirred at room temperature for about 1 hour. Then, cyclohexylmethyl amine (0.26 mL, 2 mmol) and DIEA (0.35 mL, 2 mmol) were added and the reaction mixture was stirred overnight at RT. Then, S-(-)-2-aminomethyl-N-ethyl pyrrolidine (0.29 mL, 2 mmol) and DIEA (0.35 mL, 2 mmol) were added and the reaction mixture was refluxed overnight. The reaction mixture was diluted with ethyl acetate and washed with brine. The organic layer was separated and dried over sodium sulfate, filtered, and concentrated under reduced. The crude material was purified by column chromatography eluding with 96:3:1 methylene chloride:methanol:conc. ammonium hydroxide to yield a white solid 141 (0.400 g, 43.7percent), mp 68-69¡ã C.; HPLC: Inertsil ODS-3V C18, 40:30:30 [KH2PO4 (0.01 M, pH 3.2): CH3OH: CH3CN], 264 nm, Rt 8.2 min, 97.1percent purity; MS (ESI): m/z 458 (M+H, 100), 362 (2.8), 230 (85.4).

The synthetic route of 22795-99-9 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; Timmer, Richard T.; Alexander, Christopher W.; Pillarisetti, Sivaram; Saxena, Uday; Yeleswarapu, Koteswar Rao; Pal, Manojit; Reddy, Jangalgar Tirupathy; Krlshna Reddy, Velagala Venkata Rama Murali; Sridevi, Bhatlapenumarthy Sesha; Kumar, Potlapally Rajender; Reddy, Gaddam Om; US2004/209880; (2004); A1;,
Chiral Catalysts
Chiral catalysts – SlideShare

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.1121-22-8,trans-Cyclohexane-1,2-diamine,as a common compound, the synthetic route is as follows.

12.65 g of anhydrous magnesium sulphate (105.1 mmoles) and 4.2 ml of a racemic trans-1,2-diaminocyclohexane mixture (35.0 mmoles) were successively added to a solution of 6.66 ml of 2-pyridylaldehyde (70.0 mmoles) in 50 ml of absolute ethanol. The reaction mixture was stirred for 20 hours at ambient temperature (the solution turned yellow after stirring for three hours), heated for 2.5 hours under reflux, then filtered through a frit. The isolated solid was washed with dichloromethane. The total filtrate was concentrated completely under reduced pressure to isolate an ochre solid, which was re-crystallised from ethanol. 8.2 g of pale yellow crystals were obtained, which corresponded to a 80.1% yield. The characteristics were as follows: M.Pt: 140-141 C. (EtOH) (racemic mixture) (Lit: 127-129 C.: obtained by Belokon, Y N; North, M: Churkina, T D; Ikonnikov, N S; Maleev, V I; Tetrahedron 2001, 57, 2491-2498 for the stereoisomer 1S,2S, hexane-MeOH); 1H NMR/CDCl3: delta 8.51 (m, 2H, H1,2), 8.28 (s, 2H, H7,14), 7.84 (m, 2H, H4,17), 6.55-7.64 (m, 2H, H5,16), 7.14-7.21 (m, 2H, H3,18), 3.50 (m, 2H, H8,13), 1,81 (m, 6H, H10,11 and H carried by carbons 9 and 12 located in the position cis (or trans) with respect to the adjacent nitrogen atoms), 1.40-1.53 (m, 2H, H carried by carbons 9 and 12 located in the trans (or cis) position with respect to the adjacent nitrogen atoms). 13C NMR/CDCl3: delta 161.42 (C7 and C14), 154.61 (C6 to C15), 149.21 (C1 and C2), 136.39 (C4 and C17), 124.43 (C3 and C18), 121.29 (C5 and C16), 73.53 (C8 and C13), 32.70 (C9 and C12), 24.33 (C10 and C11). FAB+ (NBA matrix): 293 (100%, M+1), 107 (52%, 2-pyridylaldimine+H+), 92 (38%, C5H4N-CH2+), 119 (25%, C5H4N-CHN-CH2+), 294 (23%, M+2), 204 (22%, [M-(2-pyridylidene)]+), 79 (21%, pyridine+), 187 (20%, M-[2-pyridylineamino]+), 585 (1%, 2M+1).

1121-22-8, 1121-22-8 trans-Cyclohexane-1,2-diamine 43806, achiral-catalyst compound, is more and more widely used in various fields.

Reference£º
Patent; Taillefer, Marc; Cristau, Henri-Jean; Cellier, Pascal-Philippe; US2005/234239; (2005); A1;,
Chiral Catalysts
Chiral catalysts – SlideShare

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.673-06-3,D-Phenylalanine,as a common compound, the synthetic route is as follows.

673-06-3, In 50ml dried single necked flask, 0.5g(R) -2-amino-3-phenylpropanoic acid dissolved in 4ml THF and 1ml of water, At RT., add 0.127g (1.05eq) of sodium hydroxide to make alkaline, stirred for 30min,cooled to about 0 deg.C. Slowly dropped 0.727g (1.1eq) (Boc)2O in THF solution. Naturally warm to RT and react for 3h. The reaction was stopped, the low temperature regulator 3 to PH = 4 and extracted 5 times with EA and extracted,washed with water and saturated brine, dried and concentrated to give a light brown oil 412mg.

673-06-3 D-Phenylalanine 71567, achiral-catalyst compound, is more and more widely used in various fields.

Reference£º
Patent; Shandong Kaisen Pharmaceutical Co., Ltd.; Wu, Junjun; Li, Rui; Jiang, Xiangsheng; Song, Jiaqi; Yang, Shuangbing; Zhang, Jingyu; Zhang, Erli; (37 pag.)CN105294669; (2016); A;,
Chiral Catalysts
Chiral catalysts – SlideShare

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.22795-99-9,(S)-(1-Ethylpyrrolidin-2-yl)methanamine,as a common compound, the synthetic route is as follows.

22795-99-9, General procedure: 2-(7-Aza-1H-benzotriazole-1-yl)-1,1,3,3-tetramethyluronium hexafluorophosphate (HATU; 1.2 equivalents) was added to a solution of the corresponding alpha-methyl carboxylic acid (2) (1 equiv), the appropriate amine (1.5 equiv) and DIEA (2 equiv) in dry acetonitrile (10 mL) at room temperature under argon atmosphere. The reaction mixture was stirred at room temperature overnight. Solvent was evaporated under reduced pressure, and the crude product was purified using a Teledyne Isco Combiflash? Rf purification machine using 0-10percent CHCl3/methanol as eluent to provide the desired amides 3-59 in 68-95percent yields.

As the paragraph descriping shows that 22795-99-9 is playing an increasingly important role.

Reference£º
Article; Mathew, Bini; Snowden, Timothy S.; Connelly, Michele C.; Guy, R. Kiplin; Reynolds, Robert C.; Bioorganic and Medicinal Chemistry Letters; vol. 28; 12; (2018); p. 2136 – 2142;,
Chiral Catalysts
Chiral catalysts – SlideShare

With the rapid development and complex challenges of chemical substances, new drug synthesis pathways are usually the most effective.1121-22-8,trans-Cyclohexane-1,2-diamine,as a common compound, the synthetic route is as follows.

Trans-lambda ,2-diaminocyclohexane (5.7Og, 50 mmol) is dissolved in water (10 ml_). ^-tartaric acid (3.75g, 25 mmol) is added incrementally to the solution while continuously stirring and once completely added to the solution, the mixture is heated to 900C. When all the tartaric acid is dissolved, glacial acetic acid (5 ml_, 85 mmol) is added dropwise while stirring. The mixture is heated for 1 hour at 900C whereafter it is cooled to room temperature. The resultant white J.-1 ,2-diaminocyclohexane~l.-tartrate is filtered and washed twice with cold water (5 nnL), 3 times with methanol (5 mL) and oven dried. The salt is recrystallized out of hot water and cooled overnight at 50C.The recrystallized ^-1 ,2-diaminocyclohexane-Wartrate (18.9g, 72.62 mmol) is added to 4 equivalents of sodium hydroxide (11.62g, 290.49 mmol) dissolved in water (100 mL). Once the amine has dissolved it is extracted 5 times with 100 mL portions of dichloromethane. The extracted dichloromethane portions are added together and dried with anhydrous sodium sulphate. Most of the solvent is removed by vacuum distillation. The last portion of solvent is removed in atmospheric pressure to avoid the amine from distilling under vacuum using an air condenser. Yield: 23% (overall).The optically pure amine was then applied to prepare optically pure Pt(fr”a/7s-M ,2-diaminocyclohexane)CI2 by a method described in lnorganica Chimica Acta (1985) 108 : pp 63-66 (the content of which is incorporated herein by reference), from pure K2PtCI4, 1121-22-8

The synthetic route of 1121-22-8 has been constantly updated, and we look forward to future research findings.

Reference£º
Patent; PLATCO TECHNOLOGIES (PROPRIETARY) LIMITED; WO2006/24897; (2006); A1;,
Chiral Catalysts
Chiral catalysts – SlideShare